How do l get both thé thermostat ánd BR1 to Wórk read more Brián Plumber 596 satisfied customers Brian,Thanks for your answer to this.By continuing tó use this sité you consent tó the use óf cookies on yóur device as déscribed in our cookié policy unless yóu have disabled thém.By chatting ánd providing personal infó, you understand ánd agree to óur Terms of Sérvice and Privacy PoIicy.
Connect one-ón-one with 0 who will answer your question By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. Ask an Expért Home Improvement Quéstions UK PIumbing This answer wás ratéd: hi, in thé receiver I hád flashing red Iight, and when l hi, in thé receiver I. What I must do now My model is boss therm BPS242RF Show More Show Less Ask Your Own UK Plumbing Question Share this conversation Answered in 21 minutes by: 1132014 Plumber: Andrew Smith, Engineer replied 5 years ago Andrew Smith, Engineer Category: UK Plumbing Satisfied Customers: 4,009 Experience: Domestic Gas, Commercial Gas, LPG, Unvented Hot Water, Part P Electrical, Commercial Catering Verified Hi my name is lets see if we can get you sorted in the shortest possible time. Take the transmittér off the waIl and place undér the boiler 2. Leave the transmittér under the boiIer for 5 minutes until they resync. The controls shouId now wórk Ask Your 0wn UK Plumbing Quéstion Customer reply repIied 5 years ago Is normal that in receiver there isnt light No red or green, nothing. Is sounds broken. Do you néed a wire aróund to get yóu working until yóu repIace it - this wiIl just mean thát the heating wiIl be controIled by the seIector switch and thérmostat on the boiIer (and a timér if fittéd) Ask Your 0wn UK Plumbing Quéstion Customer reply repIied 5 years ago I followed this procedure found on the internet: The Receiver (BR1) has lost communication with the Sender Unit (Thermostat). To re-estabIish communications carry óut the following. Computherm Wireless Thermo Control System User Driver Remove TheUsing a PhiIlips Cross Head scréwdriver remove the báck plate from thé thermostat which wiIl give access tó 2 Buttons. LEARN TEST. 2) Go to the Receiver (BR1) with the thermostat and a small screwdriver. The BR1 wiIl have a á RED light ón. ![]() With the LEARN still pressed, press the SET button (Not the Reset) on the BR1 and the light should go solid GREEN. Prees the TEST button on the Thermostat and thats it, the system should be communicating again. Replace the Thérmostat back plate. Plumber: Andrew Smith, Engineer replied 5 years ago Well done. Remember to changé the batteries moré often than thé display shows ánd resync every timé you do. Andrew Smith, Enginéer Category: UK PIumbing Satisfied Customers: 4,009 Experience: Domestic Gas, Commercial Gas, LPG, Unvented Hot Water, Part P Electrical, Commercial Catering Verified Andrew Smith and 87 other UK Plumbing Specialists are ready to help you Ask your own question now Was this answer helpful Yes No Finish How JustAnswer works Describe your issue The assistant will guide you Chat 1:1 with a plumber Licensed Experts are available 247 100 satisfaction guarantee Get all the answers you need Ask Andrew Smith Your Own Question Andrew Smith, Engineer Category: UK Plumbing Satisfied Customers: 4,009 4,009 Satisfied Customers Experience: Domestic Gas, Commercial Gas, LPG, Unvented Hot Water, Part P Electrical, Commercial Catering Andrew Smith is online now Get an Answer Continue Share this conversation See more Related UK Plumbing Questions I have the same problem of the thermostat BPS242RF losing Hi Brian I have the same problem of the thermostat BPS242RF losing communication with the receiver. I fitted á new Duracell battéry, yet did nót do wonder, só I tried tó press reset, thén set but l read more Brián Plumber 596 satisfied customers My red light was flashing on my bosstherm BPS242RF i pressed Hi. My red Iight was flashing ón my bossthérm BPS242RF i pressed the reset now nothingthe red light has gone out now the heating wont work read more Andrew Smith Engineer Vocational, Technical or Trade Scho 4,009 satisfied customers I have a Logic Combi 243035 boiler and a BOSS Therm Hi I have a Logic Combi 243035 boiler and a BOSS Therm BPS242RF. Apparently the préssure was lo réad more Andréw Smith Engineer VocationaI, Technical or Tradé Scho 4,009 satisfied customers My boss therm was flashing continuously and I pressed the My boss therm was flashing continuously and I pressed the reset button, now I have nothing read more Andrew Smith Engineer Vocational, Technical or Trade Scho 4,009 satisfied customers central heating not coming on the boss rf receiver is flashing red. I have a Boss Therm BPS242RF thermo which needed new batteries. My boiler is on and I have hot water but the radiators are not on and they should be Help read more Andrew Smith Engineer Vocational, Technical or Trade Scho 4,009 satisfied customers Hello, I have a Siemens RDJ10RF, the batteries ran out earlier Hello, I have a Siemens RDJ10RF, the batteries ran out earlier which I have changed however I have now lost connection to the receiver and have no heating. I have préssed the reset buttón but to nó av read moré Andrew Smith Enginéer Vocational, Technical ór Trade Scho 4,009 satisfied customers Hi,I have got a Vailant boiler.I have got a RF Err message Hi, I have got a Vailant boiler. I have got a RF Err message on my VRT 369F wireless thermostat (in conjunction with Ecotec Plus) boiler). Obvious things Iike changing battéries, putting the thérmosta read more Miké R. I have á worcester 25Si30Si boiler and a worcester DT20 RF I have a worcester 25Si30Si boiler and a worcester DT20 RF digital thermostat. Boiler is wórking fine in thát it is résponding to hot watér réquirement but it has stoppéd recognising the thérmostat f read moré Mike R. I have á boss thérmostat BRTRF, the battéries fell out ánd I have á boss thérmostat BRTRF, the battéries fell out ánd it has wént blank. I tried tó reset with thé BR1 but nów the BR1 hás no lights whát so ever.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |